موضوع: نگارش ها و آپدیت های باکس Riff در این تاپیک

صفحه 2 از 8 اولیناولین 1234 ... آخرینآخرین
نمایش نتایج: از شماره 16 تا 30 از مجموع 110
  1. #16 RIFF BOX - ROVER PC EVO V7, MARVELL PXA3XX Generic NAND DCC Loader 
    مدیر بازنشسته انجمن
    شماره عضویت
    5137
    تاریخ عضویت
    Jan 1970
    ارسال ها
    10,267
    تشکر
    405
    تشکر شده 3,164 بار در 566 پست
    RoverPC Evo V7 resurrection is simple. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence is not required; connection can be established with detached board.


    To resurrect RoverPC Evo V7:

    * Solder JTAG cable to RoverPC Evo V7 JTAG pads;
    * Connect USB cable to phone and PC;
    * Make sure RoverPC Evo V7 is selected in the list of models;
    * Make sure a fixed TCK frequency is selected;
    * Click Resurrect button;
    * Wait till software signals a successful operation completion;
    * Disconnect USB cable, de-solder JTAG wires;

    Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original firmware downloader software to restore it to the working state.


    To enter download mode:

    * Disconnect PC cable;
    * Insert battery;
    * Hold both ‘Volume Down’ and ‘Camera’ keys and press Power-On.


    21.03.2011 MARVELL PXA3XX NAND Generic DLL Released

    * Resurrector PXA3XX contains only NAND DCC Loader, thus it is to be used only for operations on DCC Read/Write page in the JTAG Manager.

    Embedded DCC Loader is designed to work inside of MCU's internal RAM memory, thus it is not sensitive to external SDRAM configuration or availability or its physical state.

    21.03.2011 - RIFF Box Firmware v1.21

    Firmware 1.21
    ---------------------------

    * Added RX-polling feature (debugger-to-target) for PXA3XX DCC transfers.

    RIFF BOX firmware is able now to wait (if resurrector DLL will request so) for PXA3XX target to be ready to accept
    next packet over DCC: this feature slows down a little the JTAG-to-Target DCC
    transfers but guaranties no packets loss for slow clocked targets;


    Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.
    پاسخ با نقل قول  
     

  2. #17 Samsung GT-B7330 Omnia PRO Boot Repair Supported 
    مدیر بازنشسته انجمن
    شماره عضویت
    5137
    تاریخ عضویت
    Jan 1970
    ارسال ها
    10,267
    تشکر
    405
    تشکر شده 3,164 بار در 566 پست
    22.03.2011 Samsung GT-B7330 Omnia PRO Boot Repair Supported

    Please start JTAG Manager and click “Check for Updates” button. You’ll be notified about new DLL, download it and restart the software.
    “Samsung_B7330.dll” contains pinout, instructions and required repair files for Samsung GT-B7330 OmniaPRO Unbrick – Boot Repair.
    پاسخ با نقل قول  
     

  3. #18 RIFF JTAG Updates - HTC Ozone/Chief, JTAG Manager v1.29 and more 
    مدیر بازنشسته انجمن
    شماره عضویت
    5137
    تاریخ عضویت
    Jan 1970
    ارسال ها
    10,267
    تشکر
    405
    تشکر شده 3,164 بار در 566 پست
    Resurrecting HTC Chief is easy:
    Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL to 0.44.0000 SPL version.
    Additionally, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘CEDA10000′.
    As well, you can change CID – for this make sure ‘Repair Custom ID’ field is checked in the Resurrection Guide dialog.


    To resurrect HTC Chief:

    *
    * Solder JTAG cable to HTC Chief JTAG pads;
    * Make sure HTC Chief is selected in the list of models;
    * Insert battery and connect USB Cable;
    * Click Resurrect button;
    * Wait till software signals a successful operation completion;
    * Disconnect power supply, de-solder JTAG wires;

    Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.


    31.03.2011 JTAG Manager v1.29, RIFF Box Firmware v1.21 released

    JTAG Manager 1.29
    —————————

    *
    * Fixed bug with plugins managing in case there is more than 1 plugin DLL available;
    * Currently selected plugin is remembered now and will stay on next startups;
    * Fixed Access Violation error during software startup in case there is none resurrector DLL present;
    * Added Reset Method selection feature for more precise reset operation when Custom Target Settings is active;
    * Updates manager & Updates tracking were completely reworked, and now are based not on the system time but on file’s hashing.
    Thus since now on the JTAG Manager’s installation folder can be copied/moved/re-installed (whatever else) without need to re-download full set of files again.
    * (SDK): more functions are now available (exported) for future Resurrector DLLs;
    * Many cosmetic changes;
    * FINALLY: “healed” the optimized DLL loading scheme:
    User shall see: “Found and Initialized: XXX New and YYY Old External Repair Pack(s)” where XXX must be always non-zero only on first startup after there were new DLLs downloaded from the support.
    On following JTAG Manager startups XXX shall be always equal to zero (!!!)
    For example, after downloading 3 more new DLLs while there were 100 Resurrector DLLs already installed, after JTAG Manager restarts user shall see:
    Found and Initialized: 3 New and 100 Old External Repair Pack(s)
    on next and all following restarts user shall see:
    Found and Initialized: 0 New and 103 Old External Repair Pack(s)
    * Re-worked balloon hints system – Own (not windows’) balloons are shown, so no matter now what are the windows’ tray icon settings are.
    * Added balloon hints for cases when target is not detected, error code 0×45, Device Id = 0x000000E1.
    Don’t forget that balloons hints can be switched on or off from the DCC Read/Write page – click “Notifications…” and select”For Advanced Users” page to see settings
    * - JTAG Manager now has new Icons http://www.jtagbox.com/wp-includes/i...icon_smile.gif
    * - Improved JTAG Manager restarting during updating itself

    Firmware 1.21
    —————————

    *
    * Added RX-polling feature (debugger-to-target) for PXA3XX DCC transfers.

    RIFF BOX firmware is able now to wait (if resurrector DLL will request so) for PXA3XX target to be ready to accept
    next packet over DCC: this feature slows down a little the JTAG-to-Target DCC
    transfers but guaranties no packets loss for slow clocked targets;

    31.03.2011 RIFF Data Exchange Plugin 1.00 released


    First release of the RIFF Data Exchange Plugin: please download it, and then select it on Usefull Plugins page in the JTAG Manager to read short description about the plugin’s abilities. In short it allows RIFF BOX users to share and use Full Image files in centralized manner without need to waste a lot of time for browsing countless forums.


    Because of big sizes of Full Image files, we don’t host them, instead users share links to file sharing servers where the files are actually uploaded. (like megaupload.com, rapidshare.com and others) You can browse existent links for required image file or share your image file (by sharing a http link) to help other RIFF BOX users.


    If you share image file please take attention to carefully fill file details so for other people this to be an easy task to search for required file (link)
    If you used link to download file and found it good or bad or link to be broken – please Rate this link so other users see the usability of the link.
    At the moment of first release of this plugin there are already few links shared so you’ll catch the idea fast.


    Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.


    www.jtagbox.com
    پاسخ با نقل قول  
     

  4. #19 HTC Advantage X7510 (HTC Athena) Unbrick - Boot Repair supporte 
    مدیر بازنشسته انجمن
    شماره عضویت
    5137
    تاریخ عضویت
    Jan 1970
    ارسال ها
    10,267
    تشکر
    405
    تشکر شده 3,164 بار در 566 پست
    Resurrection of HTC Athena is easy. Most convenient is to have USB cable connected and battery inserted.
    If during connection progress bar in JTAG Manager keeps running from 0 to 100% press with stylus the reset button on the phone (reset button is near to the JTAG pads).
    Resurrector will reflash IPL and SPL areas. You can select SPL version to be flashed in the settings window which popups before resurrection. IPL which is flashed: “ATHENA IPL DVT 2.02 H3” version.
    Current resurrector works only with HTC Athena hardware revisions which have DiskOnChip H3 memory chip installed. If you have hardware revision with DiskOnChip G4 memory chip used then select different resurrector.
    To resurrect HTC Athena with DiskOnChip H3:

    * Solder JTAG cable to HTC Athena JTAG pads;
    * Insert battery and connect USB cable to phone and PC;
    * Make sure HTC Athena is selected in the list of models;
    * Click Resurrect button;
    * Wait till software signals a successful operation completion;
    * Disconnect USB cable, de-solder JTAG wires;

    Now phone is in bootable condition, that is, even if it does not start up normally you can flash it using known flashing methods.
    To enter download mode:

    * Disconnect PC cable;
    * Insert battery;
    * Hold ‘Camera’ key and press ‘Power ON’ key or use stylus to press ‘Reset’ button. In few seconds you should see TriColor picture.

    Additional info:

    * DiskOnChip H3′s full NAND memory chip is divided into partitions by the internal memory controller. Thus DCC Loader creates virtual FLASH chip for each partition – you can read/write these partitions by selecting proper ROM index (“Access ROMi Address Space”) on the JTAG Manager’s DCC Read/Write page;
    * DiskOnChip H3 has no spare zones, thus only Main field must be used during write operations. ECC Enable checkbox has no meaning here.

    Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.


    http://www.jtagbox.com/jtag-news/rif...air-supported/
    پاسخ با نقل قول  
     

  5. #20 CDMA Samsung B159, Samsung Galaxy Mini (S5570) Supported 
    مدیر بازنشسته انجمن
    شماره عضویت
    5137
    تاریخ عضویت
    Jan 1970
    ارسال ها
    10,267
    تشکر
    405
    تشکر شده 3,164 بار در 566 پست
    Resurrecting Samsung B159 is simple. Board is auto powered on when battery is inserted and USB cable is connected.
    Resurrector re-flashes only firmware zone of the phone (0×000000 to 0x57FFFF).



    To resurrect Samsung B159:

    * Solder JTAG cable to Samsung B159 JTAG pads;
    * Connect ignition cable for auto power on or use battery;
    * Make sure Samsung B159 is selected in the list of models;
    * Click Resurrect button;
    * Wait till software signals a successful operation completion;
    * De-solder JTAG wires;

    Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.
    Special thanks goes to Mr Lalitg.

    06.04.2011 Samsung Galaxy Mini (S5570) Unbrick – Boot repair supported


    Samsung S5570 resurrection is simple. Phone is auto powered when USB Data Cable is inserted while battery is inside. If you don’t use USB cable, make sure to hold Power On button during JTAG connection establishing phase.


    To resurrect Samsung S5570 do this:

    * Solder JTAG cable to Samsung S5570 JTAG pads;
    * Insert battery and connect USB cable to phone and PC;
    * Make sure Samsung S5570 is selected in the list of models;
    * Click Resurrect button;
    * Wait few seconds until software signals a successful operation completion;
    * Disconnect USB cable, de-solder JTAG wires;

    Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.
    To enter download mode:

    * Disconnect PC cable;
    * Insert battery;
    * Hold both ‘Volume Down’ and ‘Home’ keys and press Power-On to enter Download Mode;

    Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.
    پاسخ با نقل قول  
     

  6. #21 Samsung S7230E Wave 723 Unbrick – Boot Repair supported 
    مدیر بازنشسته انجمن
    شماره عضویت
    5137
    تاریخ عضویت
    Jan 1970
    ارسال ها
    10,267
    تشکر
    405
    تشکر شده 3,164 بار در 566 پست
    Resurrecting Samsung S7230E is easy. To power the phone connect USB cable and insert battery. In case phone is not detected de-power phone completely, then wait few seconds, insert USB cable and then insert battery.


    To resurrect Samsung S7230E:

    * Solder JTAG cable to Samsung S7230E JTAG pads;
    * Connect USB cable to phone and PC;
    * Insert battery;
    * Make sure Samsung S7230E is selected in the list of models;
    * Click Resurrect button;
    * Wait till software signals a successful operation completion;
    * Disconnect USB cable, de-solder JTAG wires;

    Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state. We used MultiLoader 5.64 version.


    To enter download mode:

    * Disconnect PC cable;
    * Insert battery;
    * Hold both ‘Volume Down’ (on the left side of phone) and ‘Lock’ (right side bottom part) keys and press Power-On.

    Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.
    پاسخ با نقل قول  
     

  7. #22 HTC 7 Mozart Unbrick, Unlock, IMEI Repair, CID Repair, ModelID Repair sup 
    مدیر بازنشسته انجمن
    شماره عضویت
    5137
    تاریخ عضویت
    Jan 1970
    ارسال ها
    10,267
    تشکر
    405
    تشکر شده 3,164 بار در 566 پست
    Resurrecting HTC Mozart is easy. Phone is auto powered on with USB Data Cable connected to the PC while battery is connected.
    In case you have no USB cable near, make sure battery is charged enough and hold Power On button during initiation of JTAG connection.
    Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL to 0.60.1000 version. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PD6710000′.


    To resurrect HTC Mozart:

    * Solder JTAG cable to HTC Mozart JTAG pads;
    * Insert USB Data cable into board and PC;
    * Make sure HTC Mozart is selected in the list of models;
    * If you use battery, press Power On key;
    * Click Resurrect button;
    * Wait till software signals a successful operation completion;
    * Disconnect power supply, de-solder JTAG wires;

    Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.
    To enter download mode:

    * Disconnect PC cable;
    * Insert battery;
    * Hold ‘Volume Down’ key and press ‘Power ON’ button.

    Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.
    پاسخ با نقل قول  
     

  8. #23 ساپورت سامسونگ sch-s109 توسط ریف باکس 
    مدیر بازنشسته انجمن
    شماره عضویت
    5137
    تاریخ عضویت
    Jan 1970
    ارسال ها
    10,267
    تشکر
    405
    تشکر شده 3,164 بار در 566 پست
    Resurrecting Samsung S109 is simple. Phone is auto powered on with charger connected; battery presence is not required.
    Resurrector re-flashes only firmware zone of the phone (0×000000 to 0x3FFFFF).


    To resurrect Samsung S109:

    * Solder JTAG cable to Samsung S109 JTAG pads;
    * Connect ignition cable for auto power on or use battery;
    * Make sure Samsung S109 is selected in the list of models;
    * Click Resurrect button;
    * Wait till software signals a successful operation completion;
    * De-solder JTAG wires;


    20.04.2011 JTAG Manager v1.31, RIFF Box Firmware v1.23 released


    Whats new :


    JTAG Manager 1.31

    * “RUN/STOP” Loaders functionality is added (and alternative to the DCC Loaders)

    This is required for some ARM7 cores when Debug Communication Channel (DCC) to/from core is not functional (like in MSM6000)


    Firmware 1.23

    * Added 8/16/32-bit bus read/write access rotuines for ARM7 core
    * ARM7 debug is now available in ARM/Thumb modes (use the GDBServer for this);


    Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

    RIFF Box – JTAG Revolution
    پاسخ با نقل قول  
     

  9. #24 RIFF JTAG - CDMA Haier C3010, LG LSP450T Repair supported 
    کاربر رسمی
    شماره عضویت
    80114
    تاریخ عضویت
    Jan 1970
    ارسال ها
    807
    تشکر
    271
    تشکر شده 183 بار در 74 پست
    22.04.2011 CDMA Haier C3010, LG LSP450T Repair supported


    Resurrecting Haier C3010 is simple. Phone is auto powered on with USB Cable connected to the PC. Battery presence is not required; connection can be established with detached board.
    Current resurrector contains Firmware and EEPROM zones for memory chips with IDs 0x00EC/0x257E and 0x017E/0×2210. Proper data will be selected automatically depending on memory ID in your device.


    To resurrect Haier C3010:

    Solder JTAG cable to Haier C3010 JTAG pads;
    Insert USB Data cable into board and PC;
    Make sure Haier C3010 is selected in the list of models;
    Click Resurrect button;
    Choose which areas to flash;
    Wait till software signals a successful operation completion;
    De-solder JTAG wires;

    Resurrecting LG LSP450T is simple. Phone is auto powered on with USB Cable connected to the PC. Battery presence is not required; connection can be established with detached board.
    Current resurrector contains Firmware and EEPROM zones for memory chip with ID 0×0020/0×8867


    To resurrect LG LSP450T:

    Solder JTAG cable to LG LSP450T JTAG pads;
    Insert USB Data cable into board and PC;
    Make sure LG LSP450T is selected in the list of models;
    Click Resurrect button;
    Choose which areas to flash;
    Wait till software signals a successful operation completion;
    De-solder JTAG wires;

    Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

    RIFF Box – JTAG Revolution
    پاسخ با نقل قول  
     

  10. #25 RIFF JTAG - CDMA Samsung S239 (MPower) Repair supported 
    کاربر رسمی
    شماره عضویت
    80114
    تاریخ عضویت
    Jan 1970
    ارسال ها
    807
    تشکر
    271
    تشکر شده 183 بار در 74 پست
    درود.




    26.04.2011 CDMA Samsung S239 (MPower) Repair supported


    Resurrecting Samsung S239 is simple. Phone is auto powered on with USB Cable connected; battery presence is not required.


    To resurrect Samsung S239:

    Solder JTAG cable to Samsung S239 JTAG pads;
    Connect ignition cable for auto power on or use battery;
    Make sure Samsung S239 is selected in the list of models;
    Click Resurrect button;
    Wait till software signals a successful operation completion;
    De-solder JTAG wires;

    Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.


    RIFF Box – JTAG Revolution
    پاسخ با نقل قول  
     

  11. #26 ترمیم b2710توسط ریف ساپورت شد. 
    مدیر بازنشسته انجمن
    شماره عضویت
    5137
    تاریخ عضویت
    Jan 1970
    ارسال ها
    10,267
    تشکر
    405
    تشکر شده 3,164 بار در 566 پست
    Samsung B2710 resurrection is simple. Phone is auto powered on when USB Cable and battery are connected.
    To resurrect Samsung B2710 do this:

    * Solder JTAG cable to the Samsung B2710 JTAG pads;
    * Connect USB cable to phone and PC;
    * Make sure Samsung B2710 is selected in the list of models
    * Click Resurrect button;
    * Wait few seconds until software signals a successful operation completion;
    * Disconnect USB cable, de-solder JTAG wires;

    Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.
    To enter download mode:

    * Disconnect PC cable;
    * Insert battery;
    * Hold both ‘Volume Down’ and ’9′ keys and press Power-On. Screen lights up with Download mode message.

    Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.
    پاسخ با نقل قول  
     

  12. #27 ترمیم بوت گوشی سامسونگ i9023 پشتیبانی شد. 
    مدیر بازنشسته انجمن
    شماره عضویت
    5137
    تاریخ عضویت
    Jan 1970
    ارسال ها
    10,267
    تشکر
    405
    تشکر شده 3,164 بار در 566 پست
    Resurrecting HTC Incredible C is easy. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence is not required; connection can be established with detached board.
    Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PB3120000′.


    To resurrect HTC Incredible C:

    * Solder JTAG cable to HTC Incredible C JTAG pads;
    * Insert USB Data cable into board and PC;
    * Make sure HTC Incredible C is selected in the list of models;
    * If you use battery, press Power On key;
    * Click Resurrect button;
    * Wait till software signals a successful operation completion;
    * Disconnect power supply, de-solder JTAG wires;

    Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.


    To enter download mode:

    * Disconnect PC cable;
    * Insert battery;
    * Hold ‘Volume down’ key and press ‘Power ON’ button to enter HBoot menu;
    * Hold ‘Volume up’ key and press ‘Power ON’ button to enter Recovery mode;




    04.05.2011 Samsung Nexus S (i9023) Unbrick Boot repair supported


    Samsung I9023 is based on the S5PCxxx Processor (ARM core is Cortex-A8).
    Note, one simple way to connect over JTAG – connect USB cable to PC and insert battery. In this case phone is automatically powered on. But note, in very rare cases it is possible that you will have to hold Power On key during initial connection.
    Current resurrector has two different versions of primary boot loaders (PBL) embedded. This depends on hardware version of your phone which boot to use, thus in case of failure (cannot enter download mode after resurrection) of first loader try selecting another.
    In case after resurrection (after you have tried with both boot versions) the download mode is not initiated (LCD remains blank) do repeat resurrection with ‘Clone Gremlin zone’ option checked.


    To resurrect Samsung I9023:

    * Solder JTAG cable to Samsung I9023 JTAG pads;
    * Connect microUSB cable to phone and PC;
    * Insert battery;
    * Make sure Samsung I9023 is selected in the list of models;
    * Make sure a fixed TCK frequency is selected;
    * Click Resurrect button;
    * Wait till software signals a successful operation completion;
    * Disconnect USB cable, de-solder JTAG wires;

    Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.


    To enter download mode:

    * Disconnect PC cable;
    * Insert battery;
    * Hold both ‘Volume Down’ and ‘Home’ keys and press Power-On.

    Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.
    پاسخ با نقل قول  
     

  13. #28 ترمیم s5830, a867توسط ریف ساپورت شد. 
    مدیر بازنشسته انجمن
    شماره عضویت
    5137
    تاریخ عضویت
    Jan 1970
    ارسال ها
    10,267
    تشکر
    405
    تشکر شده 3,164 بار در 566 پست
    Samsung S5830 resurrection is simple. Phone is auto powered when USB Data Cable is inserted while battery is inside. If you don’t use USB cable, make sure to hold Power On button during JTAG connection establishing phase.


    To resurrect Samsung S5830 do this:

    Solder JTAG cable to Samsung S5830 JTAG pads;
    Insert battery and connect USB cable to phone and PC;
    Make sure Samsung S5830 is selected in the list of models;
    Click Resurrect button;
    Wait few seconds until software signals a successful operation completion;
    Disconnect USB cable, de-solder JTAG wires;

    Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.


    To enter download mode:

    Disconnect PC cable;
    Insert battery;
    Hold both ‘Volume Down’ and ‘Home’ keys and press Power-On to enter Download Mode;

    12.05.2011 Huawei E5830 Broadband modem Unbrick – Boot repair supported


    Resurrecting Huawei E5830 is simple. Just make sure you solder all JTAG signals. Connection can be established with USB Cable connected, though in some rare cases battery presence may be required.
    If modem is not detected by RIFFBOX JTAG, disconnect JTAG connector, re-insert modem into USB and then connect back the JTAG connector.
    Please note, if only an USB cable is connected the device is detected by PC as unknown device. So, after resurrection in order to check if modem is alive make sure battery is connected.


    To resurrect Huawei E5830:

    Solder JTAG cable to Huawei E5830 JTAG pads;
    Insert Huawei E5830 modem into any USB port for power;
    Make sure Huawei E5830 is selected in the list of models;
    Click Resurrect button;
    Wait till software signals a successful operation completion;
    De-solder JTAG wires;

    12.05.2011 Samsung Eternity A867 Unbrick - Boot repair supported


    The Samsung A867 board is auto powered on with USB Data Cable connected to the PC. Battery presence is not required; connection can be established with detached board.


    To resurrect Samsung A867:

    Solder JTAG cable to Samsung A867 JTAG pads;
    Connect USB cable;
    Make sure Samsung A867 is selected in the list of models;
    Click Resurrect button;
    Wait till software signals a successful operation completion;
    Disconnect power supply, de-solder JTAG wires;

    Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.


    To enter download mode:

    Disconnect PC cable;
    Insert battery;
    Hold both ‘Volume Down’ and ‘Camera’ keys and press ‘Power ON’ button.

    Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.
    پاسخ با نقل قول  
     

  14. #29 RIFF JTAG - Samsung GT-i8700 Omnia 7 , Samsung W299 Duos Unbrick - Boot repair suppor 
    مدیر بازنشسته انجمن
    شماره عضویت
    178
    تاریخ عضویت
    Jan 1970
    ارسال ها
    9,241
    تشکر
    36
    تشکر شده 177 بار در 107 پست
    سلام
    دو مدل I8700 و w299 به ليست ساپورت اين غول بوتي اضافه شدند.
    کد:
    Resurrecting Samsung I8700 is simple. Phone is auto powered on with USB Data Cable connected to the PC while battery is inside. In case you use the battery only please note you will have to press Power On key once. To resurrect Samsung I8700:
    • Solder JTAG cable to Samsung I8700 JTAG pads;
    • Make sure Samsung I8700 is selected in the list of models;
    • Insert Battery into phone and connect USB cable (in case you not use USB cable, press once the Power ON key on the phone)
    • Click Resurrect button;
    • Wait till software signals a successful operation completion;
    • Disconnect USB cable, de-solder JTAG wires;
    Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods. To enter download mode:
    • Disconnect PC cable;
    • Insert battery;
    • Hold both ‘Volume Up’ and ‘Camera’ keys and press ‘Power ON’ button. In few seconds phone enters download mode.
    Resurrecting Samsung W299 is simple. Phone is auto powered on with USB Data Cable connected to the PC while battery is inside. In case you use the battery only please note you will have to press Power On key once. To resurrect Samsung W299:
    • Solder JTAG cable to Samsung W299 JTAG pads;
    • Make sure Samsung W299 is selected in the list of models;
    • Insert Battery into phone and connect USB cable (in case you not use USB cable, press once the Power ON key on the phone)
    • Click Resurrect button;
    • Wait till software signals a successful operation completion;
    • Disconnect USB cable, de-solder JTAG wires;
    Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.
    پاسخ با نقل قول  
     

  15. #30  
    مدیر بازنشسته انجمن
    شماره عضویت
    5137
    تاریخ عضویت
    Jan 1970
    ارسال ها
    10,267
    تشکر
    405
    تشکر شده 3,164 بار در 566 پست
    سامسونگ Galaxy S II ساپورت شد.


    کد HTML:
    With new release we added support for new ARM core(s) - Cortex-A9 in single core and multicore configuration.
    
    Project now supports Unicode, so there is Russian and Chinese language available !
    
    JTAG Manager now supports 64bit addressing, thus allowing You to dump large memory chips (eMMC and iNAND) !
    
    New resurrectors DLL-s
    
    
    - Samsung Galaxy S II (Samsung i9100) Unbrick, Boot repair
    - SonyEricsson x10 Unbrick, Boot repair
    - Samsung CDMA B119
    
    Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.
    پاسخ با نقل قول  
     

صفحه 2 از 8 اولیناولین 1234 ... آخرینآخرین

موضوعات مشابه

  1. پاسخ ها: 5
    آخرين ارسال: 21 Sep 12, 18:23
  2. اموزش رایت فول فلش با riff
    توسط ali-tadayon در انجمن RIFF-BOX
    پاسخ ها: 1
    آخرين ارسال: 01 Jan 12, 16:15
  3. پاسخ ها: 0
    آخرين ارسال: 24 Oct 11, 16:15
  4. پاسخ ها: 0
    آخرين ارسال: 13 Apr 11, 11:40
  5. اضافه شدن 3 مدل LG در آپدیت CDMA باکس Riff
    توسط Farzad.M در انجمن RIFF-BOX
    پاسخ ها: 4
    آخرين ارسال: 24 Nov 10, 23:33
برچسب برای این موضوع

نمایش برچسب ها

مجوزهای ارسال و ویرایش
  • شما نمی توانید موضوع جدید ارسال کنید
  • شما نمی توانید به پست ها پاسخ دهید
  • شما نمی توانید فایل پیوست ضمیمه کنید
  • شما نمی توانید پست های خود را ویرایش کنید
  •